Thanks for clarifying AJ! Sounds interesting!

AJ, hope you're doing well! As I'm understanding the advertising here, is Pearl a DSP or is it like a Bluetooth "belt pack" DAC/Amp?

Decided once again to sell my BlueSound Node 2i. It's been sitting in its original packaging for over half a year after I decided I would hang onto it back in April. However, I've chosen to let it go since it really doesn't get any use. It's been reset to factory conditions and has been...

Selling my beloved Focal Celestee. Includes everything in the original package. By everything, I mean original box, cable, case, foam, packing material, tape, etc... Took very good care of these guys so hope they go to a wonderful home! I can include some custom cables if you want, we can chat...

Bumping.

Selling my beloved Focal Celestee. Includes everything in the original package. By everything, I mean original box, cable, case, foam, packing material, tape, etc... Took very good care of these guys so hope they go to a wonderful home! I can include some custom cables if you want, we can chat...

Unfortunately, my RAD-0's would've been way out of warranty anyways. This was just a mode of failure I wasn't expecting. Yea in comparison, it's definitely not bad. I forgot how much pads cost since the last time I've ever had to replace a pair was long long ago. Focal pads though... are...

Has anyone had their RAD-0 pads come unglued? Both my pads had their adhesive weaken significantly and they both more or less just slid right off the headphone leaving a bit of stickiness on the sides of the cup. Just ordered a replacement but man they are pricy pads...

I was able to swap the board myself. About 8 total screws and 3 sets of pin-board headers (super easy to pull out, just pull perpendicular).

Going to entirely agree with you here. Until I hear back from Anson, I'm a little hesistant about this device and can't really recommend it given the THD+N and overall SNR. I'm still waiting to hear back to see if this is entirely a software issue that can be rectified easily or a major hardware...

Note that the specs of the Pegasus have changed since its original pre-release specifications. Errata is in the top of the initial post. Pretty major changes to the THD and output power IMO.

Theoretically, Anson is suggesting that a software update is going to fix this. Will update as soon as i know more. Following up on this daily right now.

Talking to Awedyo Audio [where I got mine - he has a direct line to Anson], it's being looked into. Anson is currently working on a fix apparently and hopes to ship the fix soon. Don't take this as a review, but I'm also, on initial impressions, hearing it to be quite weird and not what I...

Reached out to Burson about this a while ago. I had an old edition USB card in mine. It requires a specific USB OTG cable to go C-C. They were willing to upgrade my card to the latest card for $50 which fixes this issue and let’s you use any USB cable without an OTG adapter.

Oh yea same issue with everything unplugged and nothing at all hooked up. Probably I’m just using way too sensitive stuff. My IEM’s are all 16Ohm and >105dB/mW… so yea definitely a gear pairing issue I suppose. I barely notice any noise with a RAD-0.

I'm going in from an RME ADI-2 DAC FS via XLR. Opamps are 4x of the Sparkos 3602's. What headphones/iem's are you using, just so I have a benchmark for what "quiet" is haha.

Just swapped in a new front panel PCB + Screen that I was sent from Burson. This fixed both the loud buzzing sound coming from it as well as actually the screen flicker. All that's left is a general low-level noise floor. It's definitely not silent still. However, this level of noise I can...

According to distributors, Dethonray is going to start shipping their new BT DAC/Amp, Pegasus SG1, this month! I have the black color on order, hoping to put out some impressions soon and compare to the Honey H1 and iFi GoBlu. Specifications： Input Bluetooth only Output 3.5 Single...

As long as L+/L-/R+/R- remain separate [always feasible on >4 wire cables], it can always be reterminated to balanced as a general rule. :D Nothing should prevent an original 3.5mm JH cable from going to a 2.5mm at all.

Did you ever get this resolved? I am also getting a really faint crackling sound with my unit when I turn the volume knob. Only happens when music is playing and it is super quiet, out of the 4.4mm balanced.

Reached out to Burson when I made that post, haven't heard back just yet. I've talked to them before about a dead remote though, and they happily shipped me a replacement PCB without any questions. I had told em no need to send the whole remote, since I can just PCB swap it myself. We'll see...

In terms of height, I felt like the Indigo portrayed the effect slightly better, but the Sharona had more space laterally and depth. If I were to say, the Sharona seems more like a wide fan out from the head, with a bit of a height added, but the Indigo seemed more like a cone from the center of...

I had a chance to spend some time with both. Borrowed friend’s indigo for about half and hour and did some AB’s. Sharona feels like overall a much darker signature compared to the Indigo. The indigo is a very safe and neutral tuning with a solid amount of detail and tech capabilities. The...

You know what, I'm hearing two types of buzz as well. 1. I will hear a static-like noise [kind of like those old TV sets] at a fairly higher pitch throughout the board. This doesn't change at all when I change my volume/mute/input/brightness/gain. However, it goes away immediately when I swap...

Hmmm pretty sure it's not. I had the issues with the Vivid V6's and I've had this unit for about a year now, with the same amount of noise from both the V6's and the Sparkos ones. I had thought the noise floor was normal, until I was reading some other reviews about it being dead quiet.