Search results
  1. ujamerstand

    Hand built custom headphones

    To be honest, it might be an easier starting point for you to modify something like a fostex t50rp before building headphones from scratch. It's cheap, it'll be a good experience to learn about headphone construction, damping and frequency response; best of all there are a ton of information...
  2. ujamerstand

    Hand built custom headphones

    Quote:   OP clearly asked if those specs = good sounding driver.   Quote:
  3. ujamerstand

    Hand built custom headphones

    Those specs are unimportant. What's important is the driver's frequency response and distortion values. You'll probably have to measure those yourself.
  4. ujamerstand

    My DIY electrostatic headphones

    That's a terrific FR response. CSD curves are remarkably similar to the 007s as well. Congratulations!   Did he happen to take distortion measurements for the headphones as well?
  5. ujamerstand

    My DIY electrostatic headphones

    Ah, you are using the same material as I am then. I am using a much thicker piece though. 5/8 inch stuff from ebay. 
  6. ujamerstand

    My DIY electrostatic headphones

    I like your rubber gasket. :) I couldn't find one appropriate, so I used caulk instead.
  7. ujamerstand

    The Stax thread (New)

    It's great to see more people setting up their own measurement rigs. We really need to get our own thread going, somewhere to discuss the effect of various materials on the result, what should we consider as neutral results, and how can we process the raw data to get rid of the coupler's...
  8. ujamerstand

    The Stax thread (New)

    Results looking good! We see the importance of getting a good seal when measuring stats cans. :)   What is PUF? Does it stand for polyurenthane? If so, my measurements conforms to yours.
  9. ujamerstand

    Raspberry Pi & DIY

    which chip? You'll have to load the right ALSA device driver. I remember that TI's pcm2702 usb dac works right out of the box.   Also, I'd simply go headless on the thing. If you really need to, xtunnel to the thing via ssh.
  10. ujamerstand

    The Stax thread (New)

    Quote:   I have purchased over a hundred c3675s, and I can confirm your sentiment. 
  11. ujamerstand

    Do Objective Headphone Measurements Correlate to the Audiophile's Subjective Experience?

    The raw uncompensated measurements are exactly what they are, raw measurements where the microphone's response and other artifacts introduced by the measurement rig are not corrected.
  12. ujamerstand

    Redirection Spam on smartphone

    The problem persists. This time appeared while I was browsing the orthodynamic thread.
  13. ujamerstand

    Some LME49600 implementations

    Quote:   OT, but they are on a rolling production schedule. I'm set to receive mine near the 28th.
  14. ujamerstand

    Some LME49600 implementations

    Newark is farnell's US branch. Get a raspberry pi while you're at it.
  15. ujamerstand

    Is anyone building the KGSSHV?

    Looks like a good rig. How'd you like it with the smyth realiser thus far?
  16. ujamerstand

    The Stax thread (New)

    FYI, Woo buys their stuff through Yamas, which runs staxusa.
  17. ujamerstand

    Toronto Meet - Sunday April 8th

    Looks like I won't be able to make it this time... You guys have fun!
  18. ujamerstand

    Toronto Meet - Sunday April 8th

    If I can finish my kgsshv on time. Too busy to work on it ATM.
  19. ujamerstand

    Toronto Meet - Sunday April 8th

    If I can make it, I'll try my best to bring my kgsshv with me.
  20. ujamerstand

    Toronto winter meet? [interest check]

    I might be interested in hopping in the carpool. I live downtown as well.    Quote: Did you fix the imbalance issue? If I finish the kgsshv before the meet happens I could try to bring it along with me.  
  21. ujamerstand

    Stax Sigma wood mesh housing?

    Quote: I would if it didn't cost so much. I think it's at least 120 dollars for the two cups. That's a spendy failure if the structure flexes and causes coloration... There's always making the backplate with steel bronze, but I think it's too costly and too heavy. I'll look more closely...
  22. ujamerstand

    My DIY electrostatic headphones

    Birgir, you know I'm all up for the diffuse field EQ. ;)
  23. ujamerstand

    MuppetFace's TakeT H2+ Thread

    Quote: Bleed money off you.  
  24. ujamerstand

    LCD3 Measurements

    Could we get the O2 amongst these charts as well?
  25. ujamerstand

    Headamp Blue Hawaii Special Edition

    I see there are some "Blue" Hawaii in the mix! :D
Top