Recent content by RamblerBoy
  1. RamblerBoy

    Roll call: Indians staying in India, interested in high end headphones/IEMS

    Still up for sale. https://www.head-fi.org/threads/india-beyerdynamic-dt880-chrome-special-edition-600-ohms-headphone.869789/ https://www.olx.in/item/beyerdynamic-dt880-headphones-ID1hhkrf.html
  2. RamblerBoy

    Roll call: Indians staying in India, interested in high end headphones/IEMS

    Just had a short listen it's definitely better through the idsd.. i mean my hd800s than what it sounded directly out of the fiio x5iii or mojo. But for some unknown (edit: well known) reason i prefer line out from x5iii and into idsd as opposed to pure digital fed into the dsd. That way it...
  3. RamblerBoy

    Roll call: Indians staying in India, interested in high end headphones/IEMS

    I received it today morning (28/1/2018). Since i did not receive a genuine buyer so far, I unboxed it and had a short listen to it for about 5-10 minutes after which i repacked it. It is still up for sale. I already have an HD800S and I don't prefer having two headphones at a time (**edit...
  4. RamblerBoy

    Fiio x7 mark ii - output impedance - Shure SE846

    Thanks a ton. I am starting to feel that i'll never find something that puts out a truly flat response with the shures.
  5. RamblerBoy

    Fiio x7 mark ii - output impedance - Shure SE846

    I am thinking the same too.. and the same reason why i feel that mojo is clearer compared to fiio. Maybe because it is more expensive and maybe because i think too much because as i have mentioned earlier, the fiio is just fine when i don't brood upon it. It's like when i am looking for...
  6. RamblerBoy

    Fiio x7 mark ii - output impedance - Shure SE846

    That sounds wise. Thanks.
  7. RamblerBoy

    Fiio x7 mark ii - output impedance - Shure SE846

    Maybe that is what it is.. X7ii's fr curve shows a roll off below 50 hz with a 32 ohm load (fiio's website) while X5iii has it below 15-16 hz. Mojo too has a slight roll off in the sub bass. Is it right to believe that this the reason why i am getting increased rumble with the x5iii? And the...
  8. RamblerBoy

    Fiio x7 mark ii - output impedance - Shure SE846

    Thank you so much... The reason why its bothering me is because i had the mojo untill last week (owned for about 1.5 years)..had to sell it to buy x5iii... so i am basically talking out of memory; seems like the mojo is (in my mind) a lot clearer than the x5iii.. only if i had it with me atm to...
  9. RamblerBoy

    Fiio x7 mark ii - output impedance - Shure SE846

    But wouldn't the sound signature change? I have read comments that the x7ii is more neutral and transparent as opposed to x5iii. The x5iii is warm and dark and paired with the se846, it is slightly a bit too warm or syrupy or veiled. But i am also thinkig if the x5iii proves good when it...
  10. RamblerBoy

    Fiio x7 mark ii - output impedance - Shure SE846

    Thank you so much for your valuable inputs guys.. i already have the fiio x5iii so i guess i might put up the response curve on the thread mentioned above this week. Was thinking about upgrading to x7ii. Only now did i read about the method used to measure it (rmaa, etc..)
  11. RamblerBoy

    Fiio x7 mark ii - output impedance - Shure SE846

    So you mean to say that it isn't safe to get the fiio x7 mark ii?
  12. RamblerBoy

    The RMAA (RightMark Audio Analyzer) Source and Audio Device Measurement Thread [Overview of Measurements in Post #3, Tutorial in Post #2]

    Does anyone have the fiio x7 markii and fiio x5iii to test with the shure se846 and post the fr curve here?
  13. RamblerBoy

    Fiio x7 mark ii - output impedance - Shure SE846

    Hey guys, I have a doubt.. is it advisable to plug the Shure SE846 having impedance of 9 ohms into the Fiio X7 Mark II having output impedance of 1.2 ohms? Will it really alter the the sound properties of the Shure SE846? Please do reply, i am really interested in buying the Fiio X7II. Thank...
  14. RamblerBoy

    Fiio X5 3rd gen || 2x AKM 4490 || Balanced Out || DSD || DXD | DTS | Android || Dual Card Slot

    Hey guys, 1) when using viper's eq is it advisable to lower the freqs i perceive are exagerated like in any other eq or can i simply increase the levels of the subdued ones? 2) Will the effect be the same when increasing the subdued ones and decreasing the overall output gain?
  15. RamblerBoy

    The Deals DISCUSSION Thread (READ THE FIRST POST!!!)

    Will idsd bl micro get any discount this black friday? Does anyone know?
Top