Recent content by miky2011
-
The "Lovely Cube" Headphone Amp (Lehmann Black Cube Linear Clone)
Francisdemarte, DIP are working right. I have tested with multimeter the on/off function. I'm in Spain. Barcelona. You think that MKP1837 (22nF) capacitors round the opamp can have any problem? Its the only one that I have not change.- miky2011
- Post #870
- Forum: Headphone Amps (full-size)
-
The "Lovely Cube" Headphone Amp (Lehmann Black Cube Linear Clone)
Hi francisdemarte, I tried with three differents op-amps : stock lovely 2134, stock lovely 2111AM and an original 2134 (wich appears in the photos) with the same result and same poor amplification.- miky2011
- Post #866
- Forum: Headphone Amps (full-size)
-
The "Lovely Cube" Headphone Amp (Lehmann Black Cube Linear Clone)
Thanks for your posts. Chetlanin, you say that the main problem maybe is in the op-amp. But ....Where is the problem? All components are in place. I have reflow the solders... resistors and capacitors are in right values. What I can see in the PCB? What I...- miky2011
- Post #864
- Forum: Headphone Amps (full-size)
-
The "Lovely Cube" Headphone Amp (Lehmann Black Cube Linear Clone)
Hello, I checked all the components in place and value. I think that all is right in this sense. The only thing that I dont have tested is Pot ALPS. What is the easiest way to check it? It´s necessary remove from PCB? I want to thank to everyone the valuable...- miky2011
- Post #862
- Forum: Headphone Amps (full-size)
-
The "Lovely Cube" Headphone Amp (Lehmann Black Cube Linear Clone)
Hello, here I am with my problem. I have reviewed all solders. I have tested dip switches for gain function properly off and on. All components are in place. I have measured voltages with digital multimeter: - BD140 BD139: collector-base .-...- miky2011
- Post #847
- Forum: Headphone Amps (full-size)
-
The "Lovely Cube" Headphone Amp (Lehmann Black Cube Linear Clone)
I still have the problem. With the gain at 0db. I have not amplification. I have to put the volume to maximum to hear the same volume as I listen to my Sansa Clip + directly. Even a little less with "lovely". With the gain to 10, 18 and 20dB I have changes in the output sound. I...- miky2011
- Post #844
- Forum: Headphone Amps (full-size)
-
The "Lovely Cube" Headphone Amp (Lehmann Black Cube Linear Clone)
Hi Francisdemarte, 0db = lovely cube only pass the sound without amplification? Its that true? I have doubts about that ...- miky2011
- Post #842
- Forum: Headphone Amps (full-size)
-
The "Lovely Cube" Headphone Amp (Lehmann Black Cube Linear Clone)
Hi francisdemarte, Tomorrow i will can show someter picture My source: Sansa clip+ Gain: 0db Its a must make the solder on two sides of PCB? I make the solder only in one side (upside resistors and downside rest of componentes). Thats right or is an error?- miky2011
- Post #839
- Forum: Headphone Amps (full-size)
-
The "Lovely Cube" Headphone Amp (Lehmann Black Cube Linear Clone)
A greeting to everyone. I just received the Kit of Lovely Cube this afternoon. I have welded all components. The problem is that the sound its very low even to max. volume. I use 150ohm. headphones and the volume its same as directly connected to Ipod. All three leds...- miky2011
- Post #837
- Forum: Headphone Amps (full-size)
-
The "Lovely Cube" Headphone Amp (Lehmann Black Cube Linear Clone)
I think to use panasonic FM capacitors 470uF/35v. (Very low impedance) There are good capacitors for that?.- miky2011
- Post #836
- Forum: Headphone Amps (full-size)
-
The "Lovely Cube" Headphone Amp (Lehmann Black Cube Linear Clone)
Fixed bug.... are 10R... Wirebound best that Metal Film? ..... OK ....- miky2011
- Post #835
- Forum: Headphone Amps (full-size)
-
The "Lovely Cube" Headphone Amp (Lehmann Black Cube Linear Clone)
Blablabla, beautiful answer and very useful for me. Thanks. a) I think "Lovely Cube" use 10R/1W Wirebound Resistors and "Original BCL" use Metal Films Resistors. Its that true? b) This green capacitors are 0.1uF/400V. in the Lovely Cube...- miky2011
- Post #833
- Forum: Headphone Amps (full-size)
-
The "Lovely Cube" Headphone Amp (Lehmann Black Cube Linear Clone)
For example, this image. Make zoom. You will see 400v. http://www.alicemagicbox.com/image/lovelycubenichicon01.jpg- miky2011
- Post #831
- Forum: Headphone Amps (full-size)
-
The "Lovely Cube" Headphone Amp (Lehmann Black Cube Linear Clone)
Ok, I followed the thread from beginning to end. I have some doubts about some components: a) The four output resistors 10R/1W 1%. Is it better to be "Metal Film Resistors" or "Wirewound Resistors"? . I have both (Vishay) types and I have no idea what to ride...- miky2011
- Post #829
- Forum: Headphone Amps (full-size)
-
The "Lovely Cube" Headphone Amp (Lehmann Black Cube Linear Clone)
Great thread !!! Thanks for your answers ... I bought the "LovelyCube" for the fun of being able a "exact" copy of Lehmann BCL. That's my goal. That is the reason why I like to know what type of components is mounted in the Lehmann Original. Some are named along the...- miky2011
- Post #825
- Forum: Headphone Amps (full-size)