discus123's latest activity
  • discus123
    discus123 reacted to kkugel's post in the thread Home-Made IEMs with Like Like.
    Hey man, layer height of 0.05 is sufficient for great detail. You'll save some time ;) Oh and double lift height to 8, as well as lift...
  • discus123
    discus123 reacted to Aldo40's post in the thread Home-Made IEMs with Like Like.
    Do not create holes, if you use chitubox, this software may automatically create a hole for the removal of resin. In your slicer...
  • discus123
    discus123 replied to the thread Home-Made IEMs.
    thanks your advise. I will make change and print the shell again. Do I need to change the printer setup also. please take a look for...
  • discus123
    discus123 replied to the thread Home-Made IEMs.
    I'm completely new on 3D printing. That hole is created by the 3D printing software. If I don't dig a hole inside the shell, after...
  • discus123
    discus123 replied to the thread Home-Made IEMs.
    This batch of shells just taken out from my 3D printer this morning, it seems quite smooth and solves all my probelms facing in previous...
    • Snap1.png
    • Snap2.png
    • Snap3.png
  • discus123
    discus123 reacted to Aldo40's post in the thread Home-Made IEMs with Like Like.
    Excellent job;). And thanks for the method of the previous page on the tubes/shell assemblies , it’s a bit long to do but it works...
  • discus123
    discus123 replied to the thread Home-Made IEMs.
    Hello, Looks very good. I wanna to know how the faceplate firmly attached to the shell ? Can you tell more about this. Thanks !
  • discus123
    discus123 reacted to ohige's post in the thread Home-Made IEMs with Like Like.
    Hello everyone. I learned a lot from this forum and made an IEM. I am grateful to everyone who shared a lot of knowledge. I'm not good...
  • discus123
    discus123 reacted to Aldo40's post in the thread Home-Made IEMs with Like Like.
    I don’t think you need this kind of tube, they are finer and must reason a little more because they are finer, if you want to gain...
  • discus123
    discus123 replied to the thread Home-Made IEMs.
    Thanks bro, you're are great. Thanks Aldo40, nice shell you made.
  • discus123
    discus123 reacted to Theodoric Paddlefoot's post in the thread Home-Made IEMs with Like Like.
    All kudos for this marvelous shell go to Aldo40. I changed the nozzle to a whopping 6.5mm OD, if you want that I can share it. Here is...
  • discus123
    discus123 reacted to Theodoric Paddlefoot's post in the thread Home-Made IEMs with Like Like.
    A little update from my MASM 3 Pro with added 38D1X, the MASM 5 A. I've played around a bit with adding tubes right into the shell in...
  • discus123
    discus123 reacted to piotrus-g's post in the thread Home-Made IEMs with Like Like.
    Hey there sports fans apparently I have a bit too much time on my hands so here we go E50DT0005/D vs SWFK-31736 measuring conditions...
  • discus123
    discus123 reacted to Aldo40's post in the thread Home-Made IEMs with Like Like.
    yes I can do this in a few days, it will take me a little while I have projects in progress to finish
  • discus123
    discus123 reacted to mattmatt's post in the thread Home-Made IEMs with Like Like.
    What are these graphs? Bottom SWFK? Problem with Knowles' graphs. Sometimes they aren't standardized. So comparing them them via spec...
Top