Recent content by ChrisX
-
Dsavitsk/Beezar Torpedo Build Thread
I have finished the Torpedo build today. As said before I first measured the slightly mismatched 6J6 by looking at the output. Test setup was output switch set to high, 330 Ohm load resistance. As mentioned before, the DC voltage at C11/C12 was 128 V at the left, 144 V at the right channel...- ChrisX
- Post #545
- Forum: DIY (Do-It-Yourself) Discussions
-
Dsavitsk/Beezar Torpedo Build Thread
That was one pair of the kit indeed. Thanks for the offer but I plan to use the 6J6 only for initial setup and I'm going to switch to E90CC anyway, so the tubes are ok for me. Thanks for the idea about AC matching. I will try to match the best pair of my 5-pack of E90CC this way. I...- ChrisX
- Post #541
- Forum: DIY (Do-It-Yourself) Discussions
-
Dsavitsk/Beezar Torpedo Build Thread
I just finished assembling my Torpedo PCB. At first startup I have seen that the DC voltage at C11/C12 varies between 130 V at one channel and 145 V at the other channel. After exchanging the tubes the voltages followed with the tubes. Would this measurement be a good indicator for tube matching...- ChrisX
- Post #534
- Forum: DIY (Do-It-Yourself) Discussions
-
Dsavitsk/Beezar Torpedo Build Thread
I just picked up my kit from customs on Friday ... and have already the new PCB included. So which SMD caps do you recommend?- ChrisX
- Post #524
- Forum: DIY (Do-It-Yourself) Discussions
-
eXStata DIY Electrostatic Amp for Intermediate DIYers
Quote: Originally Posted by luvdunhill Also, 0.1-0.2mA is probably within the realm of error, even if you have the most accurate meter in the world. For example, if you pick the JFETs up with your fingers and place them in a test jig, you may notice slightly different readings then if...- ChrisX
- Post #2,217
- Forum: DIY (Do-It-Yourself) Discussions
-
eXStata DIY Electrostatic Amp for Intermediate DIYers
I just matched the J-FETs for my sand build. Out of a batch of 60 I found 21 with an Idss > 10 mA and out of these I could gather three quads. So statistically the recommended 20 J-FETs for one quad should turn out, but I wouldn't be sure if always. My three quads have Idss values of...- ChrisX
- Post #2,213
- Forum: DIY (Do-It-Yourself) Discussions
-
eXStata DIY Electrostatic Amp for Intermediate DIYers
My Boards arrived today. Great Work! Thanks Alex! Most of the parts are already here, but I won't have much time in the next weeks. I think I can start building in February, until then I should be able to get the remaining stuff.- ChrisX
- Post #2,118
- Forum: DIY (Do-It-Yourself) Discussions
-
Post pics of your builds....
Quote: Originally Posted by MrSlim Very Nice Job! Thanks. Quote: Originally Posted by MrSlim Where did you get the cool top grill? It's standard perforated aluminium sheet. Luckily I live in a bigger city here in Germany, so I have two professional aluminium...- ChrisX
- Post #6,244
- Forum: DIY (Do-It-Yourself) Discussions
-
Post pics of your builds....
After half a year lying naked on my bench waiting for an enclosure I finished my SOHA II today. Still to do is painting the top cover, what I will do in summer when I can spray outside (my wife will kill me if I try this in the kitchen, and rightly so ). And the potentiometer shaft has to be...- ChrisX
- Post #6,241
- Forum: DIY (Do-It-Yourself) Discussions
-
We Got Ti Kan (AMB) an HD800!
I'll also join in.- ChrisX
- Post #157
- Forum: DIY (Do-It-Yourself) Discussions
-
eXStata DIY Electrostatic Amp for Intermediate DIYers
Quote: Originally Posted by BoilermakerFan Can I parallel (3) power LEDs per channel? I need (6) for back lighting on my chassis faceplate. I would suggest connecting the LEDs in series, not in parallel. With the voltage available you can easily drive 100 of them.- ChrisX
- Post #1,835
- Forum: DIY (Do-It-Yourself) Discussions
-
eXStata DIY Electrostatic Amp for Intermediate DIYers
Quote: Originally Posted by runeight Well, as it turns out, splitting the panel will only add cost. At this point I will just get both amps and assume that they all will go out. Although I already have some tubes I would be in with a solid state amp in this case. Alex please add...- ChrisX
- Post #1,783
- Forum: DIY (Do-It-Yourself) Discussions
-
eXStata DIY Electrostatic Amp for Intermediate DIYers
Quote: Originally Posted by runeight So the order is full. One day I didn't look into head-fi, now I'm already too late. So count me in for the third run, if there will be one. In the meantime I will keep on reading all your listening impressions and building experiences. Chris- ChrisX
- Post #1,740
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
Quote: Originally Posted by zkool448 Added above some pics of dry fit.. Really Beautiful. But I would be a bit concerned about ventilation. I finished my SOHA_II this week and still without any enclosure the heatsink temperature reaches 60 °C (with a few mA below the...- ChrisX
- Post #838
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
Alex, Thanks for your diagnosis. I checked the first plate of the tubes (Pin 1) and there are the expected 19 Volts. So it's really only that my tubes are mismatched. I have four of them so I will try the others and stick with the best ones. Seems I have "luck" with mismatched parts. The 7815...- ChrisX
- Post #829
- Forum: DIY (Do-It-Yourself) Discussions