I've had my customs for a few years, they're reshelled 1964-T (triples) with standard 2 pin connectors. The connectors have become loose over the years, and my cable barely stays connected and frequently cuts out. Any recommendations on how to fix this? Do I need to pay for a full reshell to...

Hey everybody,   I've got a pair of DT990s that have had no sound on the right side for a few months now.  I've just gotten around to taking them apart to diagnose/recable them and to my surprise the cabling seems good.  I put my scope on the right driver and it's getting a signal, but no...

Hey, I'm trying to get some amount of volume control for my Schiit Modi under Linux, since my CIEMs are still way too loud on the lowest possible setting of my Magni.   Now from my understanding, the Modi does not natively support volume control, but it is possible for there to be software...

Hey, I don't know if you got this working but it was fairly straightforward for me.   To see if your system can detect the Modi, do this:   embedded-tech ~ # aplay -l **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: ALC889 Analog [ALC889 Analog] Subdevices...

I've got some questions about this before participating...   1. What qualifies as an entry? 2. What DOESN'T qualify as an entry? 3. What do we need to participate? 4. What are the design requirements?

  This just made me a lot more comfortable with my decision to go with the half-priced 1964-T compared to the V3.  Great review.

So I have come to a point where I have an option to purchase AND reshell both the Kozee Infinity X1 Executive and the 1964-T for a grand total of $500.  However, upon opening up my calculator I found that buying new of both items (with a 2nd gen 1964-v3 to boot) would put me at a total of around...

Okay, so I'm now at the decision point.  I'm leaning more towards getting the 32 ohm version of the DT990 -- would I be sacrificing anything by doing so (compared to higher impedance versions)?  With the 32 ohm version, would I be OK with getting something like the FiiO E5/6?

It'll have to be for home use.  I can just use my panasonics on-the-go.   Tomorrow I might end up shopping around for tubes -- can I just use any tube for an amp?  What specs should I be looking for?

Yeah, actually one of my friends had the VMODA LPs -- the ones with the chrome finish.  I got a chance to compare them side-by-side to my Panasonic RP-HTF600s and they sound a bit more closed, possibly more bassy.   As for headphone sightings, I've just seen a ton of people with beats...

So how do the 32, 250, and 600 ohm variants compare?  What does the higher impedance do for the quality/accuracy of the speakers?   For now I'm going to wait until I visit an electronics warehouse to see what kind of tubes they have.  Is there a list somewhere of tubes I should be looking...

This might be a silly idea, but I've got a Fender guitar amp (the Fender Super Champ) and it uses a couple tubes in its circuitry -- would I be able to just use that with 600 ohm headphones?

I'm leaning more towards building my own amp....  I've definitely got the skills and materials required (as long as that place still has some good tubes cheap).  If I get anywhere with it I'll post something in the DIY section.   Thanks for the tips and the warnings -- I had no idea that 600...

I can literally get a ton of tubes (good ones by the looks of it) for $5 each.  So, DIY amps are definitely a legitimate option here.

Ok, so is there a low-cost amp that I could use with the 600 ohms?  I'm actually planning on getting more high impedance cans later on so it might be a good investment to consider (if it's as essential as you say).   What about building my own tube amp?  There's a great electronics warehouse...

Okay, so I've been looking for some new headphones for a while now, and instead of waiting another 10 weeks and blowing ALL my money on the LCD-2 I think I'm going for the DT990-600 ohms, since they have (or from what I've heard) great bass and treble.  Any comments, warnings or suggestions...

Hello,   I'm getting to the point where I'll have enough money to do something significant with.  However, I'd love it if there were some reviews (note -- some, not just one) comparing the audeze lcd-2 with electrostat 'phones.  I'm just not sure which one I am better off investing in.  I'm...

Could you post the layout of those stators, showing measurements (hole diameter, total diameter, etc)?  I'd like to try making them myself.   I wonder if I could do this with nothing but a router table, a drill press, and a ferric chloride tub...  I don't really have the time to build a cnc...

  Hello Wachara,   Thanks for the reply -- I'm definitely going to be making these headphones. As for the mylar, how exactly is it even affected by the fields made by the stators?  I read a post regarding a special coating, but I wasn't sure how that changes things.     Thanks.

Hi Wachara   This is awesome.  I have been inspired to make my own electrostats now....   For your CNC machine, are you using stepper motors?  What software do you use with it?   This looks like something I could make to upgrade from the panasonic RP-HTF600s.  Love the picture of the...

So I've been looking into getting some open back headphones after listening to the slight openness of the Panasonic HTF-600.  (keyword - slight.  I don't really know what I'm missing though.)   I've got ~50 - 75 to spend, since I want to save up and buy an LCD-2 in like 6 months.  According...

But of course, shakugan no shana 3.  :D   I have to admit they've sorta mutilated the storyline...   Also, Tilpo: I suggest you watch angel beats first.  No reasoning behind this other than its a cool show and its on netflix instant stream.

Is it possible to mod these drivers into other cans?  :P  They're just that good.   I would think they'd fit beyerdynamics stuff, since they use the same pads.     *thanks Dsnuts profusely for mentioning these before I bought hd515s*

****!  I've owned these things for an hour and they're completely awesome!!!  The highs and mids are so crisp, and the bass sort of punches you in the gut -- they look (and feel) expensive too.  I haven't yet ordered the velours, and the pleather isn't too bad -- however, it does sort of feel...

How good is the pleather that comes with it -- is it really worth forking out an extra $20 just for some velour pads?  With these mdr-xd200s, they fit perfectly (literally!) and the pleather feels rather comfy.   Anyways, I did order the htf600s this morning and for $30 w/free shipping...