or Connect
Head-Fi.org › Forums › Equipment Forums › Portable Source Gear › Rockbox for iBasso DX50 dual boot with stock firmware
New Posts  All Forums:Forum Nav:

Rockbox for iBasso DX50 dual boot with stock firmware - Page 91

post #1351 of 1976
Quote:

Originally Posted by cholero View Post

 

Edit:
Sorry I tried again an also get (Status 7) Installation aborted. I will try to solve this.

 

This is the message error.... I stay with 1.5...

post #1352 of 1976
Quote:
Originally Posted by cholero View Post
 

Wow thank you! Finally someone confirming that 1.6.0 works with rockbox.
13hours is mot than I expected. But you were runningstock firmware if you say 240 volume, didn't you?
 

..........................

 

Sorry forgot to mention that Rockbox AluminArt used during the test, with volume at -6dB.
It was my habit of converting the "dB", steps from volume of the original stock.

 

If I am not mistaken, every step of the original firmware volume equivalent to approximately 0.5dB. Therefore, attenuation of -6dB, means reducing the volume about 12 steps, which is 243. While actually performing various adjustments during the test, the control ranged between -6 and -12 dB.

 

I reiterate my thanks for all the effort.
I will try to prove things to investigate and report possible errors.
  Greetings.

post #1353 of 1976

Hi, I have a problem with my DX50, i tried to update it to the latest 1.6 firmware and everytime I update it, the device just restarts and enters CM recovery mode. I have deleted the files in both the DX50 and SD card. I tried factory reseting it but, to no avail. Can someone help me to delte the CM mode in my DX50. Thanks

post #1354 of 1976
Quote:
Originally Posted by wlz12 View Post
 

Hi, I have a problem with my DX50, i tried to update it to the latest 1.6 firmware and everytime I update it, the device just restarts and enters CM recovery mode. I have deleted the files in both the DX50 and SD card. I tried factory reseting it but, to no avail. Can someone help me to delte the CM mode in my DX50. Thanks


Have you tried a hard reset, pushing the power button and volume up button at the same time?

post #1355 of 1976

Just did rockbox last night and I'm super impressed.  Had to turn the volume up a little to achieve the same (loudness) compared to Mango but no biggies.

 

Tried a few themes and liked them all.

 

I was having this small issue previously where I'd have 1/4 sec skips on random tracks (very rarely) but swapping to rockbox seemed to have fixed that.

post #1356 of 1976
Quote:
Originally Posted by jamato8 View Post
 


Have you tried a hard reset, pushing the power button and volume up button at the same time?

When I do this, it goes to the CWM-based Recovery Mode. Then when i do a factory reset, the same thing happens

post #1357 of 1976
Quote:
Originally Posted by wlz12 View Post
 

When I do this, it goes to the CWM-based Recovery Mode. Then when i do a factory reset, the same thing happens


Have you tried using the batch tool to load the FW? If you have a PC or a MAC that that has Windows on it, you can use this to load any FW but it can be tricky at first to get working on your computer. http://www.ibasso.com/uploadfiles/download/DX90-tools.zip

 

There are instructions on the 1st page of the regular DX90 thread. 


Edited by jamato8 - 12/2/14 at 9:09pm
post #1358 of 1976
Quote:
Originally Posted by wlz12 View Post

Hi, I have a problem with my DX50, i tried to update it to the latest 1.6 firmware and everytime I update it, the device just restarts and enters CM recovery mode. I have deleted the files in both the DX50 and SD card. I tried factory reseting it but, to no avail. Can someone help me to delte the CM mode in my DX50. Thanks

There is a problem with the 1.6.0+cwm firmware that I uploaded to sendspace. If you were using this version it explains the problem.
1.5.0+cwm works well.
post #1359 of 1976
Quote:
Originally Posted by jamato8 View Post
 


Have you tried using the batch tool to load the FW? If you have a PC or a MAC that that has Windows on it, you can use this to load any FW but it can be tricky at first to get working on your computer. http://www.ibasso.com/uploadfiles/download/DX90-tools.zip

 

There are instructions on the 1st page of the regular DX90 thread. 

Thanks, I will do this once I am at home. 

 

 

 

 

Quote:
Originally Posted by cholero View Post


There is a problem with the 1.6.0+cwm firmware that I uploaded to sendspace. If you were using this version it explains the problem.
1.5.0+cwm works well.

I tried flashing the CM firmware previously but, it wasn't successful. So, i sticked with iBasso's firmware. Suddenly when I tried to flash the new firmware, this happens

post #1360 of 1976

 

I tried flashing it with the DX90 tools but, it failed. I have tried everything including formating my DX50 but, i get this menu whenever i try to update the firmware and when i press UP and the power button at the same time. 

 

Can anyone help?

post #1361 of 1976
Quote:
Originally Posted by tingis View Post
 

If I am not mistaken, every step of the original firmware volume equivalent to approximately 0.5dB. Therefore, attenuation of -6dB, means reducing the volume about 12 steps, which is 243.

This is correct.

post #1362 of 1976
Quote:
Originally Posted by wlz12 View Post
 

I tried flashing it with the DX90 tools but, it failed. I have tried everything including formating my DX50 but, i get this menu whenever i try to update the firmware and when i press UP and the power button at the same time. 

 

Can anyone help?

This menu is the CWM menu

 

Your information is not sufficent. What firmware did you flash with DX90 tool?

 

-> I'm not sure that any cwm function works expect "install zip from sdcard" and reboot

-> If you have "stock recovery" cwm zip file on your sdcard you can flash this in cwm to get back to stock recovery, then flash any update.img (you can take out the sdcard for this and connect it directly to the pc. Maybe it needs to be formatted to fat32)

post #1363 of 1976
Quote:
Originally Posted by wlz12 View Post
 

Hi, I have a problem with my DX50, i tried to update it to the latest 1.6 firmware and everytime I update it, the device just restarts and enters CM recovery mode. I have deleted the files in both the DX50 and SD card. I tried factory reseting it but, to no avail. Can someone help me to delte the CM mode in my DX50. Thanks

 

Try installing from the CWM, the file "stock_recovery.zip" then reset and any original firmware to use.

 

File "stock_recovery.zip" here: Resources, firmware and information are available here:

https://bitbucket.org/isergachev/rockbox/wiki/Home

 

Greetings.

post #1364 of 1976
Quote:
Originally Posted by wlz12 View Post
 

 

I tried flashing it with the DX90 tools but, it failed. I have tried everything including formating my DX50 but, i get this menu whenever i try to update the firmware and when i press UP and the power button at the same time. 

 

Can anyone help?


I had problems with my DX50 because of a non iBasso FW I had placed on it. Nothing I did would get it to work. So I reformatted the DX50, which is bricking it but would be like that if there was no way to place a FW on it. the only way to fix it was with the batch tool, which is why I reformatted the internal memory, wiping it clean. Then with the batch tool, I was able to correctly load just the FW from iBasso and it has worked fine. 

post #1365 of 1976
Quote:
Originally Posted by jamato8 View Post
 


I had problems with my DX50 because of a non iBasso FW I had placed on it. Nothing I did would get it to work. So I reformatted the DX50, which is bricking it but would be like that if there was no way to place a FW on it. the only way to fix it was with the batch tool, which is why I reformatted the internal memory, wiping it clean. Then with the batch tool, I was able to correctly load just the FW from iBasso and it has worked fine. 

When i use the batch tool it fails and states: "This operation didn't do, because of not supporting"

Everytime my iBasso is in its CWM Mode, the batch tool does not show that DX50 is connected

How did you manage to flash it?


Edited by wlz12 - 12/3/14 at 6:08am
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Portable Source Gear
Head-Fi.org › Forums › Equipment Forums › Portable Source Gear › Rockbox for iBasso DX50 dual boot with stock firmware