Head-Fi.org › Forums › Sponsor Announcements and Deals › The world's first UIEM and CIEM version of Dual DD+Quad BA! LEAR BD4.2 is now availble !
New Posts  All Forums:Forum Nav:

The world's first UIEM and CIEM version of Dual DD+Quad BA! LEAR BD4.2 is now availble ! - Page 3

post #31 of 64
Quote:
Originally Posted by Q Mass View Post


I wonder if Project 86 will be getting these?

 

 

Yep, I just need to hurry up and get impressions done. I haven't had the time but I think I can do it later this week. 

post #32 of 64
That's good news.
I realise that it'll be some time until we get to read your thoughts on these, but I await them with interest :-)
post #33 of 64
Quote:
Originally Posted by lear-hk View Post

Hey guys, thanks for waiting!
Is that what you are looking for?
3308.jpg 

=) thanks. That looks like what I meant. (And good)
Why is one straight and one angled? Are they magical switchable or convrttible plugs xD?
I suspect Q Mass wanted that as well, Not sure whether the angling the socket down bit was important and why if it was.
post #34 of 64
Thread Starter 
Quote:
Originally Posted by svyr View Post


=) thanks. That looks like what I meant. (And good)
Why is one straight and one angled? Are they magical switchable or convrttible plugs xD?
I suspect Q Mass wanted that as well, Not sure whether the angling the socket down bit was important and why if it was.

 

The picture is just to show you guys how those look like at once.

You may just select between the angled or straight  or of course you may ask to doing just same as the picture too~

Reply
post #35 of 64

I am so very intrigued....

 

The universal mold looks like it is so damn thick and deep, how heavy is each of the earpiece please?

post #36 of 64
Thread Starter 
Quote:
Originally Posted by djvkool View Post
 

I am so very intrigued....

 

The universal mold looks like it is so damn thick and deep, how heavy is each of the earpiece please?

 

5g per side without cable but with a silicone tip.

Reply
post #37 of 64
That's not quite the same as the plug I was referring to.
Still looks pretty good though.
The ones I have are actual 90 degree plugs, where the cable exits at 90 degrees to the axis of the MMCX plug, rather than having to be 'bent' over.

The reason I suggested that the socket would have to be angled down a few degrees is that the 90 degree plug could cause the cable to be TOO close to the part of the ear immediately above the socket.

I'll post pic's of the plugs I mean if I can find them.
post #38 of 64


distortion figures for the bass shelf. @100spl. (re comment on one of the previous pages about 2DD )
(found on the parent company forums smily_headphones1.gif )

wonder if THD or THD+N e.g. vs http://www.innerfidelity.com/images/DunuDN1000.pdf
Edited by svyr - 2/12/14 at 3:29am
post #39 of 64
Thread Starter 
Quote:
Originally Posted by svyr View Post



distortion figures for the bass shelf. @100spl. (re comment on one of the previous pages about 2DD )
(found on the parent company forums smily_headphones1.gif )

wonder if THD or THD+N e.g. vs http://www.innerfidelity.com/images/DunuDN1000.pdf

 

 

The test must be doing with the same equipments .

And we are not going to offense other manufacturers .

So the comparison of  product to product should be tested by 3rd party as well.

 

The result above is to show that we have no regret on using dual 6mm to replace a bigger one.

And it's not a  gimmick too~


Edited by lear-hk - 2/12/14 at 4:23am
Reply
post #40 of 64
Quote:
Originally Posted by lear-hk View Post


The test must be doing with the same equipments .
And we are not going to offense other manufacturers .
So the comparison of  products should be tested by 3rd party as well.

=) all good - fair comment.
post #41 of 64
Thread Starter 

Introducing the LEAR's Handmade Acoustic Low Pass Filter inside the BD4.2 !

 

After we matched and paired the dynamic drivers for the BD4.2.(Even it is a tough work, but still not the toughest! )

 

We are step forward to the most difficult job - The making of LEAR's Handmade Acoustic Low Pass Filter for the dynamic driver!

 

195856wtwe42n4x6wqotqm.jpg

 

 

 

Why not Electronic Low Pass Filter?

 

195903b7qitzqk53mzjsks.jpg

 

Because every passive electronic components has "impedance" . No matter the world's best capacitors or inductors,they all have ESR (Equivalent series resistance)and which will be works like adding with a series resistor and influence to the overall performance!

 

The Dynamic drivers inside the BD4.2 loves electric current, the bass part of music needs a lot of power! A suitable Passive Electronic Low Pass Filter not just required more of the space inside the earphone ,but also higher up the overall impedance ! It will be significantly limiting the current and power and also brings Distortion!

 

195900ya6vq6tscxyj9ksr.jpg

 

As you can see in the test result of using an inductor (just 1 inductor!) , which is already reducing the driver's sensitivity quite a lot,and it still needs to treat to achieve our goal of what a bass driver should be!

 

Say no to such a sacrifice and compromise!


The LEAR's Handmade Acoustic Low Passive Filter is born!

 

It has no compromise and sacrifice to the "Sound Quality and Sensitivity " , It works well for our dynamic driver and which has also a quite nice roll off slope of being an earphone's bass driver unit!

 

However, the trade off is...we must make it one by one and pair and match those one by one by LEAR!

 

What a nightmare ?!

 

Thank you for all your watching and support to LEAR!

Reply
post #42 of 64

This certainly gets more and more interesting as days go by...

post #43 of 64
😲....i was waiting for this concoction 😁....two dynamic and 4 ba😎...but I can't afford it...but will slowly save up for them and see how the go in sound signature 😊
post #44 of 64

Looks very promising.

post #45 of 64

If I had to choose my final IEM , I would vote for this Lear UIEM. That technology is just blowing my head.

New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Sponsor Announcements and Deals
Head-Fi.org › Forums › Sponsor Announcements and Deals › The world's first UIEM and CIEM version of Dual DD+Quad BA! LEAR BD4.2 is now availble !