Head-Fi.org › Forums › Equipment Forums › Headphone Amps (full-size) › Amplifier picks up radio station! Help!
New Posts  All Forums:Forum Nav:

Amplifier picks up radio station! Help! - Page 3

post #31 of 39
12/14/09 at 1:58am
DANG COLLEGE KIDS AND THEIR DELINQUENT RADIO STATIONS!!
Reply
post #32 of 39
12/14/09 at 7:14am
I liked my Heed Canamp in the beginning! But after a while I got radio signals through it. I gave it away to my father in law, who lives in Russia, but he got the same problems there. So buying this unit, was a totally waste of money! Approximately 500 dollars lost!
Reply
post #33 of 39
1/13/10 at 7:59am
I´ve received a Canamp yesterday purchased from a head-fier, and found the same FM radio interference problems, mainly at lower and highest position of the volume control. Never experienced these issues with my K271´s connected to the Xonar D2 or even using my Sony receiver with a large 14 meter interconnect plugged to the Xonar too.
Tried disconnecting the input cables, plugging the heed into a different outlet, plugging hifiman RE2 with other 1/8 adapter to the amp, etc. The only thing that cancels this interference a bit is touching de 1/8 adapter while listening.
Any ideas on how to fix this ground issue?
Reply
post #34 of 39
1/13/10 at 6:40pm
I can also hear a small noise every time I press a key... C´mon! The heed is a very popular amp, I´m sure someone can help!
Could anyone solve this problem with ferrite clips?
Reply
post #35 of 39
1/16/10 at 8:21am
I thought this info might be helpful for anyone with a similar problem...
Resolved 99% of the issue with a 8mm snap-on ferrite on my K271 stock cable ( rounded a few times )
Reply
post #36 of 39
1/16/10 at 8:51am
I always thought this problem was do to a an oscillation not grounding.
Reply
post #37 of 39
1/16/10 at 9:00am
Quote:
I always thought this problem was do to a an oscillation not grounding.
I´d really wish to know about electricity, believe me.
First I´ve tested with aluminum paper covering the headphones cable with good results. Then bought the ferrite and obtanined similar results (testing all over the cable to find the perfect spot to clip on). The results are fine and a more organized - cleaner solution over my desktop.
Reply
post #38 of 39
1/16/10 at 1:04pm
there are some really cheap RCA cables that do not have "360 degree" shield termination so a small step up in IC quality can sometimes help in keeping RF out - video RCA cable would be expected to do this right

for RF it is usually more important for the signal input gnd to be connected to the chassis than the power gnd - are the input RCA gnd isolated from the chassis?

ferrite cores that power, signal IC or even headphone cable can be (separately) passed through/clamped on can also cut RF entry in some instances - although usually on by a few dB

I have read of really severe RF interference such that demodulated RF could be heard with the power off

if you can establish that it is the local transmiter you can contact their engineer - it is their responsibility to not interfere with consumer electronics (assuming the electronics in question meets EMI standards)
Reply
post #39 of 39
1/16/10 at 3:56pm
Quote:
there are some really cheap RCA cables that do not have "360 degree" shield termination so a small step up in IC quality can sometimes help in keeping RF out - video RCA cable would be expected to do this right
The RF interferences persisted even with the input cables - RCA´s were unplugged from the amp. Also plugged the Heed to many outlets with same results.
I wonder why I´ve never had these issues with my audio/computer equipment before.
Anyway, thanks for the info.
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Headphone Amps (full-size)
Head-Fi.org › Forums › Equipment Forums › Headphone Amps (full-size) › Amplifier picks up radio station! Help!