Head-Fi.org › Forums › Equipment Forums › Headphone Amps (full-size) › My Singlepower Supra Experience - Why mine almost blew up like a Hand Grenade (and yours might too)
New Posts  All Forums:Forum Nav:

My Singlepower Supra Experience - Why mine almost blew up like a Hand Grenade (and yours might too) - Page 11

post #151 of 314
8/1/09 at 6:43pm
yes that is a bleeder cap across the final power supply cap.
470k. So that cap will bleed to zero. Will take about 20 minutes.
If it was just that cap. The regulator fet would pull down the
rest of the capacitors behind it. Probably to the point where
the regulator runs out of headroom, then the leakage current
of the regulator would take over, and it could take a couple
of days to drain everything that way.

The best way to add the resistors is to get a couple of ring lugs
and solder the resistors to the ring lugs. Then after making sure
the caps are discharged, unscrew the screws and put a resistor
across each of the big caps.
Reply
post #152 of 314
8/1/09 at 6:49pm
Update for pictures on post #117
















High res: SP Extreme
Reply
post #153 of 314
8/1/09 at 6:59pm
I believe Kevin is saying to put the 100K bleeder resistors across the two large screw terminal caps, as in the marked up pic below. Kevin, correct this if wrong.
LL
Reply
post #154 of 314
8/1/09 at 7:10pm
Quote:
Originally Posted by kevin gilmore View Post
yes that is a bleeder cap across the final power supply cap.
470k. So that cap will bleed to zero. Will take about 20 minutes.
If it was just that cap. The regulator fet would pull down the
rest of the capacitors behind it. Probably to the point where
the regulator runs out of headroom, then the leakage current
of the regulator would take over, and it could take a couple
of days to drain everything that way.

The best way to add the resistors is to get a couple of ring lugs
and solder the resistors to the ring lugs. Then after making sure
the caps are discharged, unscrew the screws and put a resistor
across each of the big caps.
yes, proper drainage of those giants before even trying to put
a bleeder resistor on them. it's such a simple thing but wasn't
implemented in the first place...
Reply
post #155 of 314
8/1/09 at 7:13pm
Pars, what you posted is what I was thinking. Hope others chime in, thanks. BTW, would that be the only thing or should any other "mods" need to be implemented. Thanks.
Reply
post #156 of 314
8/1/09 at 7:26pm
that's correct mrarroyo. using a lug is recommended, as kevingilmore suggested, instead
of soldering directly on the giant cap(s).

just please make sure you discharge the cap before even attempting to put a bleeder on.
i usually tape a large value ohm and wattage resistor at end of a glass bead or rod and
touch the two ends of the resistor on the - and + ends of the cap to discharge quickly.
Reply
post #157 of 314
8/1/09 at 7:37pm
Here's a mighty ignorant "dangerous" question... I just finished having to have a bad capacitor serviced on my home's heat exchanger. I just learned how to test it--I was told to remove the capacitor and give it a charge, "any" charge would do--in my case, a 12V auto battery charger connected for say, 30 minutes.

I was told that if the capacitor was still good, I could take a screwdriver and arc the two posts--if I didn't get a spark, the capacitor was kaput. So to my question....

In a "live", working, connected system, how would someone drain these capacitors?--just let them stand for a "long" time? If so, how does one test them to insure they've been drained?

Thank you. I hope this is related enough not to be considered a hijack.
Reply
post #158 of 314
8/1/09 at 8:58pm
Quote:
Originally Posted by Pars View Post
I believe Kevin is saying to put the 100K bleeder resistors across the two large screw terminal caps, as in the marked up pic below. Kevin, correct this if wrong.
That is exactly correct.

As far as draining capacitors like this, there is a thing called a discharge stick which you can make yourself.
In this case 2 good insulated alligator clips connected to about 6 inches of wire with a 10k 5 watt resistor in
the middle. With one hand and wearing a rubber glove, clip one alligator clip on one terminal, then clip the
other alligator clip on the other terminal, then wait a minute. Use a voltmeter to verify if you want.

You will not be able to solder to those capacitors. Even if you could, it would be a very bad idea.
ring lugs like the ones already there are best. Or wrap the wires of the resistor under the screw.

ring lugs available in any decent hardware store.

Adding the resistors is a great safety thing. It guarantees that there is no charge left in any of the power
caps, and should you accidentally break a tube if you leave it off for an hour you won't risk an electric
shock removing the parts of the broken tube. Broken tubes happen ask anyone with a fender classic 60.
Reply
post #159 of 314
8/1/09 at 9:29pm
Quote:
Originally Posted by moonboy403 View Post
Transformer was running out of specs.
http://www.head-fi.org/forums/f5/war...8/#post5896971

That's the full story of moonboy's Extreme.
Reply
post #160 of 314
8/1/09 at 9:31pm
The transformer on my MPX3 is too hot to touch right now
after about an hour playing a signal. Not sure how long it takes
to reach this point.

Is this the case with other MPX3's?
Is it a serious issue?

Input appreciated from other MPX3 owners and of course Mr. Gilmore

P.S. Kevin, are your towels dry yet?
Reply
post #161 of 314
8/1/09 at 10:00pm
Quote:
Originally Posted by thathertz View Post
The transformer on my MPX3 is too hot to touch right now
after about an hour playing a signal. Not sure how long it takes
to reach this point.

Is this the case with other MPX3's?
Is it a serious issue?
A number of them get this hot.

Yes it is a serious issue. Moreso because the transformer in your
unit is 220 vac. See nate maher's recent thread.



Quote:
Originally Posted by thathertz View Post
P.S. Kevin, are your towels dry yet?
you asked for it...
http://gilmore.chem.northwestern.edu/bathroomsystem.jpg
and my favorite place to conduct business
http://gilmore.chem.northwestern.edu/bathroomphone.jpg
Reply
post #162 of 314
8/1/09 at 10:32pm
Wow, Kevin.....

Is this under-spec component issue only found in some particular lines of SP? I think we really need to check all of SP's models before they make not-so-pretty fire and toast the headphones and sources.

And I believe we are talking about full-tube amplifiers, not even hybird ones.
Reply
post #163 of 314
8/1/09 at 10:43pm
Quote:
Originally Posted by kevin gilmore View Post
A number of them get this hot.

Yes it is a serious issue. Moreso because the transformer in your
unit is 220 vac. See nate maher's recent thread.


you asked for it...
http://gilmore.chem.northwestern.edu/bathroomsystem.jpg
and my favorite place to conduct business
http://gilmore.chem.northwestern.edu/bathroomphone.jpg
Talk about 'worth a thousand words'!
The combined talents of Hollywood could not have produced
a better image

Actually my transfromer is 110v and I'm using a heavy duty step-down
converter Kevin.

Still an issue though I guess ?

Just touched the transformer again to make sure I wasn't exaggerating.
Burns like hell.
Reply
post #164 of 314
8/1/09 at 10:52pm
My MPX3's transformer is warm, but definitely not what I'd call "hot", after playing for several hours. I can keep the back of my hand on the cover as long as I like. (the back of the hand is much more sensitive to temerature than the palm-side) Mine is 110V.

Thank you, Kevin, for explaining the discharge stick!
Reply
post #165 of 314
8/1/09 at 10:56pm
Quote:
Originally Posted by thathertz View Post
Talk about 'worth a thousand words'!
The combined talents of Hollywood could not have produced
a better image

Actually my transfromer is 110v and I'm using a heavy duty step-down
converter Kevin.

Still an issue though I guess ?

Just touched the transformer again to make sure I wasn't exaggerating.
Burns like hell.
What happens if you put an egg on the trafo? Does it get cooked?
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Headphone Amps (full-size)
Head-Fi.org › Forums › Equipment Forums › Headphone Amps (full-size) › My Singlepower Supra Experience - Why mine almost blew up like a Hand Grenade (and yours might too)