Head-Fi.org › Forums › Misc.-Category Forums › DIY (Do-It-Yourself) Discussions › Does anyone have the iPhone LOD pinout?
New Posts  All Forums:Forum Nav:

Does anyone have the iPhone LOD pinout? - Page 10

post #136 of 246
2/7/09 at 8:46pm
What pins are we connecting on either side of the 66k-68k resistor?

15 + 11 --> resistor --> 21 ?
Reply
post #137 of 246
2/7/09 at 11:41pm
Quote:
Originally Posted by Hase View Post
What pins are we connecting on either side of the 66k-68k resistor?

15 + 11 --> resistor --> 21 ?
correct or you can substitute any other ground pin for 15
Reply
post #138 of 246
2/8/09 at 12:08am
I got that assembled but still got a warning when I plugged it in for a test. Is it supposed to be sporadic? Does it work for the first gens?
Reply
post #139 of 246
2/8/09 at 6:20am
It should now work with any iPod/iPhone model. Using pin 15 as ground is easiest since it's near 11 and 21. If you're still getting the message sometimes it might be that your pin 15 and 21 are somehow shorting once in awhile, possibly due to too much exposed wire touching, resistor leads touching, etc. This would bypass the resistor, and you'd end up with the message.
Reply
post #140 of 246
2/8/09 at 3:28pm
I can't get my meter to read anything but the proper resistance between 15 and 21, and between 11 and 21. Even before I jammed it all back into the connector housing, I plugged it into the phone and got the warning.

I think there's a pretty good air-gap in there.

Reply
post #141 of 246
2/8/09 at 4:37pm
Looks good to me. Perhaps you got one of the wrong pins, like 23 instead of 21? I always worry about being able to count those tiny pins correctly.
Reply
post #142 of 246
2/8/09 at 7:00pm
I counted a dozen times while I was yanking them and then again just now. I've made two in the last 24-hours the same way to the same end. Can someone with a first gen confirm that my configuration worked for them?
(that is: 11+15>33k>33k>21)

Maybe there is something happening differently in my phone...
Reply
post #143 of 246
2/14/09 at 8:35am
Hey all,
I am new to the LOD thing, please help

I read that "tying pin 11 to one of the ground pins in the LOD will activate the LOD for the second gen iPod touches".

May I know how do we "tie" pin 11 and to which ground pin (pin #?) do we tie it to? Is a resistor required for an iPod Touch 2nd Generation?

Thanks in advance!
Reply
post #144 of 246
2/14/09 at 9:25am
'tying' reffers to coupling the signal. in this case, it means making an electrical connection, or soldering a piece of wire between 2 points to 'short' them together. If you go through the last few pages of this thread, take a look at some of the pics peoople have posted, and the schematics of sorts, you should get the idea. You'll see that on top of hooking up Left, Right and Ground signals in the LOD, you also have to hook up a resistor in between some pins in order to let the ipod touch / iphone know that you want to hook up an audio device.
Reply
post #145 of 246
2/14/09 at 9:30am
Quote:
Originally Posted by ruZZ.il View Post
'tying' reffers to coupling the signal. in this case, it means making an electrical connection, or soldering a piece of wire between 2 points to 'short' them together. If you go through the last few pages of this thread, take a look at some of the pics peoople have posted, and the schematics of sorts, you should get the idea. You'll see that on top of hooking up Left, Right and Ground signals in the LOD, you also have to hook up a resistor in between some pins in order to let the ipod touch / iphone know that you want to hook up an audio device.
Thanks for the reply!

this was taken from your post earlier!

Is it a must to connect a resistor? I am getting the really small dock connector , not sure if a resistor will fit.

Can I just use a wire to connect the two points?
Lastly may I confirm that the ground wires to connect are 30&11, and 30&21?
Reply
post #146 of 246
2/14/09 at 12:21pm
for the ipod touch 2g, the above schematic works. a resistor IS required.
Note that the resistor is between (30 and 11) and (21) (ie, 21 is not connected directly to 11 or 30). I'm not sure how this functions with the iphone 3g though. The latest for that is to have (11 and 15)--|66k|--(21). This probably works for the 2g too, and may be more universal. maybe someone else can comment on that.

What is your primary use?
Reply
post #147 of 246
2/14/09 at 12:23pm
I need the LOD for listening to music on my iPod Touch 2nd Generation.

Do they sell really small SMD (surface mounted) resistors of this type? I am afraid the traditional ones will not fit into the teeny QB connector case
Reply
post #148 of 246
2/14/09 at 12:51pm
you'll have a harder time with SMD in there, specially if you don't know of their existence. I'm sure you could find a small 1/8'th Watt 1K resistor at an electronics store. The ridax dude here said it should be ok if you remove the un-needed pins, so even a normal 1/4 W 1K should fit. may need some creative packing.. but I could see it working. I'm sure any type of resistor is find in there too.. as long as it fits.
Reply
post #149 of 246
2/14/09 at 12:55pm
This is confusing.

Do I get a 66k ohm or 1k ohm resistor to fit in there? It's quite a big difference, at least it seems
Reply
post #150 of 246
2/14/09 at 1:04pm
Quote:
Originally Posted by lucifix View Post
Thanks for the reply!

this was taken from your post earlier!

Is it a must to connect a resistor? I am getting the really small dock connector , not sure if a resistor will fit.

Can I just use a wire to connect the two points?
Lastly may I confirm that the ground wires to connect are 30&11, and 30&21?
Does this work with iPhone 3G? Have you got any idea where i could purchase one?
Reply
New Posts  All Forums:Forum Nav:
  Return Home
Head-Fi.org › Forums › Misc.-Category Forums › DIY (Do-It-Yourself) Discussions › Does anyone have the iPhone LOD pinout?