Head-Fi.org › Forums › Equipment Forums › Dedicated Source Components › My Musiland M-10 Arrived! 56K!!
New Posts  All Forums:Forum Nav:

My Musiland M-10 Arrived! 56K!! - Page 4

post #46 of 72
5/1/07 at 2:44am
Thread Starter 
eMail him. He responds very quickly to emails.
Reply

Head-Fi's Best Sellers

post #47 of 72
5/1/07 at 3:21am
Thread Starter 
What I don't like: Even after modding I do not like its more front presentation of upper mids. Some recordings and loud female voices sometimes give me a feeling that I should adjust sounds with foobar EQ! With HD650, which has laid-back sound this may be a disguised blessing.

Things may improve with further burning! When it hits 250 hours perhaps.
Reply
post #48 of 72
5/1/07 at 10:13am
rlanger,

i ordered from yelzin through his email, he didn't reply for a while as he was away on holiday (early last week). However every email since has been responded to quickly..
Reply
post #49 of 72
5/1/07 at 10:20am
How does the MD10 compare to the DAC1 from benchmark???
Reply
post #50 of 72
5/1/07 at 11:49am
Thread Starter 
I think, I need to compare it with STELLO DA100. I have just bought HEADAMP GS-1 and now lack money to buy STELLO. So I may sell M10 and buy Stello. So MD10 may appear in sell section sometimes!!! If MD10 can give a head on to Stello, I will certainly buy MD10 again for its user friendly features and size.
Reply
post #51 of 72
5/1/07 at 3:56pm
Thread Starter 
There has been several PMs regarding the ease and feasibility of doing the mods. As I mentioned earlier, you need fairly good skills in SMD part desoldering and soldering to mod it.
I would be extra-careful when desoldering and removing the capacitors and diodes. The pads are so fragile. The underneath-side of the PCB has ground plane and the leads, which are attached to the opposite pole of the ground plane, are kept separated with the gorund plane with very thin margin. It is easy to short them, if one puts little more solder. If these gets shorted, the ICs will have easy premature demise with no warranty. So after soldering, it is very important to check for short circuits with a meter.
If these pads come off the PCB, it is impossible to solder them to the correct PCB trace.
Reply
post #52 of 72
5/1/07 at 5:47pm
after mod my MD10 with Rubycon ZL Caps, Vishay SF4007 diodes, LN4562 opamp, and Cardas RCA connector, there is no sound from headphone out. But everything else is fine. I was able to connect line output to my Melody H34II amp. can anyone tell me what it might be wrong with headphone output?
Reply
post #53 of 72
5/1/07 at 6:24pm
Thread Starter 
Check the solder joints of two capacitors near the headphone out. They may be getting short with the ground plane.
Reply
post #54 of 72
5/1/07 at 6:25pm
Thread Starter 
HOw do you rate the sound, after the Mods thorough the line-out?
Reply
post #55 of 72
5/1/07 at 11:26pm
After mod, the sound stage is wider and clear. Bass sounded more and heavier. I'm waiting for the OPA2827(dual ver of OPA827) to try later.
Reply
post #56 of 72
5/2/07 at 1:34am
Thread Starter 
Have you tried by-passing AC filter too?
Reply
post #57 of 72
5/3/07 at 12:34am
yes, I jumped the AC filter. That's was the first thing I did on MD10
Reply
post #58 of 72
5/3/07 at 3:15am
Thread Starter 
I am just about to sell it to buy a DA100 for comparison and DA100 will compliment my GS-1's form factor better. But I am sad to part with MD10. Unless for money shortage, I wouldn't have sold it. Later I will buy another for my bedside rig.
Now the sound-stage is huge with 3d layering and air. Very sweet beep extended bass. I am pretty impressed with this beauty. I am sure it will give a good competition for DA100.
Most impressive factor is its user-friendliness. It just remembers the user settings and can be forced to output 16 or 24 bit word length.

Quote:
after mod my MD10 with Rubycon ZL Caps, Vishay SF4007 diodes, LN4562 opamp, and Cardas RCA connector, there is no sound from headphone out.
Did you manage to get it working again?
Reply
post #59 of 72
5/3/07 at 1:22pm
I look forward to hearing your comparison, kaushama.
Reply
post #60 of 72
5/4/07 at 5:12am
Thread Starter 
Due to an error in internet ordering, I got duplicated order for parts for modding MD10. So I have one set of parts for modding in excess. I have put it in the sales section for selling as a bundle. I just want to recover the cost only. I am almost broke after the recent adventures in this hobby. If someone needs it just PM me.

It has,

Rubicon ZLH capacitors for all caps
UF4002 Vishay diodes faster than UF4007
LM4562 SOIC opamp
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Dedicated Source Components

Head-Fi's Best Sellers

Head-Fi.org › Forums › Equipment Forums › Dedicated Source Components › My Musiland M-10 Arrived! 56K!!