Sony EX90 Modding thread! - Page 11

What does the asian characters and then a date on the back of the boxes of "E" models?

EX85-was geniune in a Sony box, with a silver seal at the top corner

Me!! I got my meter from work and they measured at 29 ohms. Good test as most other parameters were very close to the original.

Mine are (were, they just got stolen on holiday) the ones with the smaller tube at the end with black writing on it. They had milled metal housings and I checked the impedance - 17ohms exactly.

Apperance is almost a completely useless test of authenticity unless you scritinize them heavily.

Now I need to get some new phones. I don't want something that goes deep in the ear, but I want something with better, punchier and deeper bass than my modded EX90's.

They are fantastic if the low frequency end is uncluttered. But if you have music, like I do, with sub-bass + kick drums + bass guitar, they just can't cope. It turns to muddy, confused bass rapidly. Which is a shame because I love the fit and the fact that they rest just inside the canal, and that they don't isolate everything. Also, the mod closes the soundstage quite a bit. They're probably a bit too airy without the mod, but they sound very close post-mod, they don't breathe.

Maybe Denon C-700 would be good for me? Any suggestions welcome. I'm going to buy another D2 (yeah, stolen) and I don't use amps.

GET THE EX-85 MODDED!!! DIFFERENT FROM eX-90:
http://www.head-fi.org/forums/f103/b...x-85-a-360261/

i wanna try some olive tips on my ex85.. Will they fit? And where do i buy them from? I dont want more than 2 pairs though.. Wanna try them first and see if i like them before i buy more..

I'm so glad I found this thread. I was thinking of buying a new pair of headphones to replace my EX85's, but modding them was like buying a new pair of headphones anyway. I tried the cling wrap mod first, and then when I found out I loved the improvement I used silicon to block the ports as some people in this thread have tried.

To anyone else who wants to try it, I found that the best way to open up a hole (since the silicon basically coats/soaks the material in the ports meaning that even scraping away some of the silicon doesn't open them up) is to stick the pin right through, until it goes through even the material in the ports.

The improvement in the bass isn't just like simply turning up the Bass in the EQ - the EX85's maintained their sound signature in the treble/mids but the bass became much more punchy and cohesive. It doesn't "create" bass where there was none before, but instead really improves the definition of the bass it produces.

I'm now keen to try out different foam tips, or some of the mods involving the foam inside the canals. I'm confused though - some of these posts lead me to believe there actually isn't any foam in the canals to remove in the EX85's, unlike the 90's?

Hmm... this thread was resurrection, but I may have to try this for myself.

What?

Do you guys think my EX90 might be a fake? I'm pretty sure I bought them directly through amazon.com. I have to pump the volume ALL the way up, and even then, it's not enough. Also, I feel like the sound is louder on the left side than the right. And when plugging them into the headphone out of my laptop, things are even worse. The sound is barely audible. Even using itunes's volume increaser preset the sound to average volume

I just tried this today w/my EX85's, and it's not too bad. I just put earbud foam over the main section w/the airvents, then poked 6 additional holes in the sectoion where you would place the iem's silicon tip. It does open the sound up, but I changed the silicon tips awhile back, so the isolation was better than w/the stock 1's.

Now, I may look for a triple flange tip for an even better seal - so thanks for the mod!!!

Sorry...

I'm just making sure I'm understanding the mod. So, is the mod basically just covering the part of the bud with the slits(Vents)with cling film? Or is there more to the mod than that? Can someone provide a better picture than the one on the first page of what the mod should look like?

Has anyone else tried putting the Shure Olives on the EX90? I actually have the 85LP and find it seemingly impossible to stretch the olives to on the 85lp, unless the ex90 is actually smaller.

I just picked up a set of NC33s and have been following this thread... not sure if they share the same driver or not, but I too removed the was filter and have found astounishing results.

Along with that, w/ comply t400s I even gained more isolation... but nothing I can do about the porting as its unfortunately sealed w/ a mic on each end